How To Thread A Brother Ls 2125

Close up of a Brother LS-2125i Sewing Machine

My husband was given this sewing machine in hopes he knew someone who could use it. It was missing the presser pes and needed a needle, but other than that, the sewing auto seems to work just fine. I had never used a Brother sewing machine earlier, so for me this was new territory. Just it wasn't long earlier I had it all set upwards for sewing. Hither is how I threaded the sewing auto.

How to Thread a Brother Sewing Machine

Threading the top thread into this machine wasn't very difficult, however the thread accept-up lever does not come up as far out of the casing every bit other machines I accept used. It may take a moment of fidgeting with it for you lot to get the thread around it. Here are the steps for threading this sewing machine.

Place your spool of thread onto the spool pivot.
Accept the end of your thread and pass it over the thread guide every bit shown in the film on the meridian of the machine next to the thread guide.
Run the thread down and around the upper tension command dial and support the other side.
Now run the thread support to the thread take-upwards and go over information technology from left to right. The thread should grab and go into the grove.
And so have the thread back down the front end of the machine to the sewing needle housing. There will exist a thread guide at the top of the needle. Run the thread through the guide, then snip the end of your thread and thread your needle from front to back.

How to Air current a Bobbin on a Blood brother Sewing Auto

Winding a bobbin on a Brother sewing auto is pretty much only similar winding on any of the other machines I have used. With this auto though, in that location is no clutch to pull out so its one less step. Here are the steps for winding a bobbin on a brother sewing machine.

Place your spool of thread on the spool pin.
Run the thread to the thread guide on the left and wrap it around co-ordinate to the picture on elevation of the automobile.
At present run the thread back to your bobbin winder.
Take your empty bobbin and run your thread from the middle of the bobbin, upwards into one of the little holes in the top disk.
Pull the thread long enough to hold it out of the fashion and place the bobbin on the bobbin winder with the thread pointed up.
Now belongings the end of your thread in your correct hand (you can guide the thread from the spool with your left), press your pedal slowly to start the bobbin winding.
Once you have the bobbin started, yous can trim the extra thread from the tiptop.
Stop winding the bobbin and when information technology stops, push the bobbin winder to the left and gently pull up to remove it from the machine.
Cut the thread and you lot are washed.

How to Put the Bobbin in a Brother Sewing Machine

This sewing machine has a front load bobbin. It can exist hard at times, especially if you have fumbly fingers similar I do, simply with a piffling patience, it volition take no time to install this bobbin. Here are the steps for how to install the bobbin.

Remove the forepart section of casing over the bobbin housing and open up the bobbin door.
Remove your bobbin case by pulling the silver bar that runs across the middle on the left hand side. The silver bar should elevator up allowing you to remove the whole case.
Holding the silver case with the open up side towards you, place your filled bobbin into it. Brand sure to pull the thread to a couple of inches long so you tin thread the bobbin.
Now holding the argent bobbin case with the arm (the weird alien 50 shaped piece on the side with the bar) facing upward and open side facing you. take the thread and run information technology up through the thread guide and into the opening next to the arm.
Holding the casing past the open bar, place the bobbin casing in to the bobbin housing with the arm and hole you lot but threaded facing up.
Once it is in place, with you acme thread already threaded, rotate your mitt bike on the right side of the motorcar until the needle goes down into the bobbin housing and then dorsum up.
Have a pair of scissors or flat object and run information technology from right to left nether the presser pes. This should bring the thread upward to join the height thread. Pull both threads a couple of inches and then motility them to the side and out of the manner. If the bobbin thread does not come up the starting time fourth dimension, repeat the steps for rotating the hand bicycle until it brings up the thread.
Shut the bobbin door and supersede the front end of your case.

Please keep in listen that we may receive a small-scale commission when you lot click our links and make purchases and as an Amazon Associate, this site earns from qualifying purchases. Notwithstanding, this does not impact our reviews and comparisons. We endeavour our best to give you an accurate representation, in order to help you make the all-time choice for you.